Dash Cam Recording Time Calculator
Estimated recording time
Enter your bitrate
Get the approximate window of footage your card can keep during continuous recording.
Compare card sizes at this bitrate
Use this calculator to estimate how much recent footage your dash cam can keep on its microSD card. Enter the card capacity in GB and the combined bitrate in Mbps of every camera that records at the same time. The result shows the hours and minutes of continuous driving footage the card can store before the camera starts replacing older clips. Check that your camera supports the card's size and type before you buy one.
A nominal 128GB card holds about 14 hours 13 minutes of continuous footage at a combined 20 Mbps, and about 9 hours 29 minutes at 30 Mbps. Both figures use the full label capacity before formatting overhead or any space the camera allocates to other uses. With loop recording switched on, that time is the window of recent footage the card keeps before new recordings replace the oldest unprotected clips. Your real window can be shorter or longer because bitrate changes with your settings, the scene and how your camera divides up the card.
How many hours do 32GB, 64GB, 128GB and 256GB hold?
The table below uses two illustrative total bitrates. The 30 Mbps column could represent a 20 Mbps front camera paired with a 10 Mbps rear camera. Every figure uses the capacity printed on the card before reserved space or formatting. Manufacturers publish their own figures for specific setups, and VIOFO lists bitrates and recording times by camera configuration.
| Card capacity | 20 Mbps total | 30 Mbps total |
|---|---|---|
| 32GB | 3h 33m | 2h 22m |
| 64GB | 7h 07m | 4h 44m |
| 128GB | 14h 13m | 9h 29m |
| 256GB | 28h 27m | 18h 58m |
Doubling the card size doubles the recording window at the same bitrate. If adding a rear camera or raising the quality setting increases the combined bitrate, the window gets shorter.
A published example from Thinkware
Thinkware publishes recording times for its U3000. For a 128GB card in Normal recording mode, Thinkware's recording time table lists 250 minutes with the front camera only and 125 minutes with front and rear cameras recording. These are Thinkware's figures for that model and mode. They differ from the table above, which uses round illustrative bitrates and the full label capacity. Treat them as one camera's published timing, and avoid using them to work out the U3000's rear bitrate.
What size microSD card should I choose?
Work through these checks in order.
- Check the manual for your exact model. Find the card type and the largest capacity the manufacturer approves. Some manufacturers recommend specific cards, as VIOFO does in its card guidance.
- Match the minimum speed class in the manual. Speed symbols appear on the card itself. The SD Association defines U3 and V30 as each specifying a minimum of 30 MB/s under their own test standards. That figure is in megabytes per second, which equals 240 Mbps. Neither symbol tells you how well a card copes with constant rewriting or whether it works in your camera.
- Consider a high endurance card. High endurance cards are designed for repeated writing, which suits a dash cam that records over itself on every drive. Card lifespan and recording window are separate questions, and the calculator only answers the second.
- Decide how much footage you want to keep. Think about your longest typical day of driving and which cameras record at once. Enter your combined bitrate in the calculator and choose a supported size that covers that window.
- Format the new card in the camera. Back up any clips you want from the old card first, then format the new one in the camera as your manual instructs. Thinkware's formatting guide shows one manufacturer's process.
What happens when the card fills?
Most dash cams record continuously in short clips. With loop recording on, the camera overwrites the oldest ordinary clip as the loop fills and keeps recording. The calculator's result is the length of that rolling window.
Some cameras can also protect saved event clips. If your model and settings support manual or G-sensor locks, pressing a save button or a sudden jolt detected by the G-sensor can protect that clip from the ordinary loop. Many of these cameras store protected clips in a separate folder, and some let you set a separate allocation, such as Thinkware's memory partition settings. Protected space can fill up too, so copy important clips off the card promptly.
The ordinary loop runs from the oldest ordinary clip through newer clips to the recording in progress. As the loop fills, each new recording overwrites the oldest ordinary clip. On cameras that support saved events, protected clips sit in a separate lane outside the ordinary loop. That protected space can fill up, so copy saved clips to another device to keep them.
Find the bitrate your camera actually uses
Dash cams record at a bitrate measured in megabits per second (Mbps). Files on your computer show their size in megabytes (MB). One byte holds eight bits, so multiply a size in MB by 8 to convert it to megabits. If a figure appears in kbps, divide it by 1,000 to get Mbps.
Your manual or the manufacturer's support pages may list the bitrate for each setting. You can also read it from a clip. Copy a representative clip from normal driving to a computer and check its properties for a total bitrate, or use its size and length.
To work it out from size and length, multiply the file size in MB by 8 and divide by the clip's length in seconds. A 150 MB clip lasting 60 seconds gives 150 × 8 ÷ 60 = 20 Mbps.
The real average rate depends on resolution, frame rate, codec and how much movement the camera sees, so a busy scene can produce a larger file than a quiet one. If your front and rear cameras save separate files, work out each rate and add them together. If one file holds both views, use its rate once.
Does parking mode change the answer?
Parking hours and stored video hours measure different things. Stored hours describe how much footage the card keeps. Parking runtime describes how long the camera stays powered while the car is parked.
How much space parking mode uses depends on the model, the mode you choose and its settings. Event-triggered recording, time lapse and low-bitrate modes can reduce the amount of data written, depending on the bitrate, how often the camera records and how the mode is set up. Some cameras keep parking footage in its own allocation. Thinkware describes the parking modes its cameras offer.
Runtime depends on the power supply, the cutoff timer or voltage setting and the operating conditions. Thinkware explains why parking mode can switch off sooner than expected. The calculator estimates stored footage only and can't predict how long your camera will stay on overnight.
For help with front and rear cameras or a parking power setup in Yorkshire, see our dash cam fitting and parking mode page.
How the calculator works out recording time
The calculator converts the card's capacity into megabits and divides it by the combined bitrate. Recording time in seconds equals usable GB × 8,000 ÷ combined Mbps. It then converts the seconds into hours and minutes.
Choose 32, 64, 128 or 256GB, or type in another capacity, then enter the total bitrate in Mbps. Enter a bitrate here, since a resolution such as 1080p or 4K doesn't tell the calculator how much data the camera writes. If you don't know your bitrate yet, select Use example to fill in 128GB and 20 Mbps. Replace those figures with your camera's own rate when you find it.
If your front and rear cameras record at the same time, enter each bitrate in its own field and the calculator adds them together once. If your figure already covers both cameras, enter it once as the total. You can also enter the usable recording space in GB if you know it, up to the size printed on the card. Without it, the calculator uses the label capacity and says so in the result.
The result shows the estimated recording window, the capacity used, the combined Mbps and whether the figures came from the example or from you. It doesn't estimate how long the camera stays on while parked, how long a single event recording lasts or how long the card will last before it wears out.
Dash cam storage FAQs
Will 64GB keep two four-hour drives with front and rear cameras?
At 30 Mbps combined, for example a 20 Mbps front camera and a 10 Mbps rear camera, a 64GB card holds about 4 hours 44 minutes. That would keep the second drive and part of the first. The figure is approximate. It uses the printed capacity, so formatting and reserved space leave a little less room, and your camera's actual bitrate may vary. Add both cameras' bitrates and enter the total in the calculator. If the result falls short of eight hours, look at the next size your camera supports. At the same 30 Mbps, 128GB holds about 9 hours 29 minutes.
When my 128GB card fills, does it erase everything or do I need to reformat it?
With loop recording on, a full card keeps working. The camera replaces the oldest ordinary clips one at a time. Formatting is a separate step that wipes the whole card, including saved clips. Copy anything you want to keep first, then format in the camera following your manual.
Can I get footage back after the card has looped over it?
Start by checking the camera's saved event folder and any copies you made earlier. Once the loop has recorded over an ordinary clip, the camera has reused that space, so don't count on getting the footage back. After any incident, save the clip with the camera's save function if it has one and copy it to another device as soon as you can.
Can parking recordings take space away from driving footage?
On some cameras, yes. If parking footage shares the same loop as driving clips, a long night of parking recordings pushes older driving clips out sooner. Other models let you set aside separate space for parking or events, such as Thinkware's memory partition settings. Where your camera offers event-only or time-lapse modes, they can reduce the data written, depending on the bitrate, how often they record and your settings.
Will a 256GB card work in my dash cam?
Only if the manufacturer supports that size for your exact model. Check the current UK manual or the manufacturer's approved card list for that model, and use the card type it specifies.
Why does my card show less space than the label?
Card makers state capacity in decimal gigabytes (GB), where 1GB is 1,000,000,000 bytes. Some computers and phones report capacity in binary gibibytes (GiB), where 1GiB is 1,073,741,824 bytes. A device showing about 119 GiB for a 128GB card is reporting broadly the same number of bytes in a different unit. Usable recording space can still be lower, because formatting and any storage the camera reserves leave less room for video. If you know the usable figure, enter it in GB in the calculator's optional usable space field. To convert a GiB figure, multiply it by 1.074.